How to Change Attachments on Kubota Skid Steer
Learning how to change skid steer attachments is fundamental for anyone wanting to maximize the machine’s performance. So, how to change attachments on Kubota Skid Steer?
In this article, we will explain how to unlock and change the attachments on your Kubota skid steer.
How to Change Attachments on Kubota Skid Steer?
The best Kubota skid steer loader is known in the industry because of its exceptional performance, versatility, and reliability. With the right tools and knowledge, you can easily change attachments on a Kubota skid steer, like a bucket or any other accessory.
Before you begin the process, ensure you are in a safe, flat area with enough space to work.
Check if you have the tools you need. What tools are needed to change attachments on a Kubota skid steer? Common tools include safety gloves, hydraulic fittings, wrenches or socket sets, and release button. This button is used to disengage the coupler mechanism that holds the attachments in place.
How to remove attachments on Kubota skid steer: Step-by-step guide
- Park the skid steer – park the skid steer on level ground and engage the parking brake to prevent any accidental movement.
- Shut off the engine – shut off the engine and remove the key from the ignition switch, also because of safety precautions.
- Lower the attachment to the ground – ensure that the attachment is on the ground and no tension is applied
- Find the release button on the coupler mechanism – this is usually located on the skid steer front, just behind the attachment. It may be labeled to identify it easily.
- Operate hydraulic controls – while holding the release button, with your other hand, operate the hydraulic controls to tilt the coupler forward or backward, depending on the position of the attachment.
- Secure the attachment to the coupler – use a wrench or socket set to loosen the bolts or pins, securing the attachment to the coupler.
- Detach the bucket from the coupler – once the bolts or pins are completely removed, carefully detach the bucket or accessory from the coupler.
- Inspect the coupler and attachment points for any damage or wear – check the coupler and attachment points for any debris, dirt, or damage, and use a brush or compressed air to clean the surface thoroughly. Address any issues before installing another attachment.
- Align the new attachment with the coupler – align the new attachment with the coupler, making sure the pinholes or bolt holes match. Be careful to avoid any misalignment or upside-down attachment.
- Insert the bolts or pins through the attachment – when inserting the bolts and pins through the attachment and the coupler, fasten them securely with a socket set or wrench.
- Test the attachment – check the attachment to ensure it runs smoothly using the hydraulic controls. Move the bucket or accessory up, down, and in different directions to make sure it operates smoothly.
How to release hydraulic pressure when changing attachments on a Kubota skid steer?
Releasing hydraulic pressure is very simple. The Kubota skid steer has a manifold block on the boom where the hose fittings are placed. Inside the manifold, there is a pressure relief. So, to release the pressure, ensure the engine is turned off and push the fittings several times into the manifold. This way, you will open up a small hole, which sends all the built-up pressure back to the hydraulic tank.
Sliding the outer ring on the female quick coupler back and the fitting will release. Be careful when laying the hoses and any other cables on the attachment to prevent them from getting damaged. Now, you are ready to get back to the machine and operate to release the attachment.
Conclusion
So, how to change attachments on Kubota skid steer? Remember that it is important to first park the skid steer on flat ground, engage the parking brake, lower the attachment, and turn off the engine. Then, you should hold the release button and use the hydraulic controls to tilt the coupler. Remove the bolts or pins attaching the current attachment and carefully detach the attachment from the coupler. Align the new attachment and secure it with pins or bolts. That’s it. If you need any help, feel free to contact us, and we’ll help you out!